Serraggio attacchi

Come legarsi "forever" alle nostre signorine.
Message
Author
User avatar
JaX
Amministratore
Posts: 4994
Joined: 11/02/2012, 23:41
Location: Roma . Abruzzo.
Contact:

Re: Serraggio attacchi

#11 Post by JaX »

Gorilla tape is like duct tape?

Inviato dal mio SM-G935F utilizzando Tapatalk

You take the red pill-you stay in Wonderland,I show you how deep the rabbit-hole goes.
https://www.carvers.it
User avatar
PabloR6
Posts: 635
Joined: 17/02/2012, 21:12

Re: Serraggio attacchi

#12 Post by PabloR6 »

pokkis wrote: 05/09/2018, 19:23 If you worry screws opening, you can put Gorilla tape over them so they dont open too much, or get lost.
I don't think that the Gorilla tape is the solution. I Think the gorilla tape doesn't work. When you carve, the slow screw ruins the thread, even if it is not lost.
User avatar
pokkis
Posts: 174
Joined: 25/11/2014, 19:30

Re: Serraggio attacchi

#13 Post by pokkis »

JaX wrote: 05/09/2018, 19:41 Gorilla tape is like duct tape?

Inviato dal mio SM-G935F utilizzando Tapatalk
Yes but with very tough with very good clue.
I have had problems with screws opening on my VistFlex, and that has been my fix.
I put piece of tape over screw end (not in thread) and that keeps screw not open (at least not too much).
Loctite, or similar, would be simpler, but due i change plates quite often, it is not good for me.
2017: XXXXXXXXXX XRRRRMSMSS MVVVSSMDDD DDMMMSMMUU U
2018: XXXXXXXXXX XXXMMMMZZZ ZZZZZZZZZZ ZZZZZZSMMM DDDDDSMS
2019: XXXXXXXXMM MMMMMMMMzz zzZZZZZZZZ ZZZzZZZzMM M
User avatar
JaX
Amministratore
Posts: 4994
Joined: 11/02/2012, 23:41
Location: Roma . Abruzzo.
Contact:

Re: Serraggio attacchi

#14 Post by JaX »

pokkis wrote:
JaX wrote: 05/09/2018, 19:41 Gorilla tape is like duct tape?

Inviato dal mio SM-G935F utilizzando Tapatalk
Yes but with very tough with very good clue.
I have had problems with screws opening on my VistFlex, and that has been my fix.
I put piece of tape over screw end (not in thread) and that keeps screw not open (at least not too much).
Loctite, or similar, would be simpler, but due i change plates quite often, it is not good for me.
This works on both feet or only the fixed one?
Do it last even under the sliding boot?

Inviato dal mio SM-G935F utilizzando Tapatalk

You take the red pill-you stay in Wonderland,I show you how deep the rabbit-hole goes.
https://www.carvers.it
User avatar
pokkis
Posts: 174
Joined: 25/11/2014, 19:30

Re: Serraggio attacchi

#15 Post by pokkis »

On VistFlex both ends slide.
2017: XXXXXXXXXX XRRRRMSMSS MVVVSSMDDD DDMMMSMMUU U
2018: XXXXXXXXXX XXXMMMMZZZ ZZZZZZZZZZ ZZZZZZSMMM DDDDDSMS
2019: XXXXXXXXMM MMMMMMMMzz zzZZZZZZZZ ZZZzZZZzMM M
User avatar
JaX
Amministratore
Posts: 4994
Joined: 11/02/2012, 23:41
Location: Roma . Abruzzo.
Contact:

Re: Serraggio attacchi

#16 Post by JaX »

pokkis wrote:On VistFlex both ends slide.
I have seen it only in photo and not the hinges.

Inviato dal mio SM-G935F utilizzando Tapatalk

You take the red pill-you stay in Wonderland,I show you how deep the rabbit-hole goes.
https://www.carvers.it
User avatar
pokkis
Posts: 174
Joined: 25/11/2014, 19:30

Re: Serraggio attacchi

#17 Post by pokkis »

It is fixed to board at both ends like basic Vist
2017: XXXXXXXXXX XRRRRMSMSS MVVVSSMDDD DDMMMSMMUU U
2018: XXXXXXXXXX XXXMMMMZZZ ZZZZZZZZZZ ZZZZZZSMMM DDDDDSMS
2019: XXXXXXXXMM MMMMMMMMzz zzZZZZZZZZ ZZZzZZZzMM M
Post Reply