Quoto Mik, Jax devi andere giu' piu' deciso con le tavole larghe, possibile che non riesci ad aprire di piu'
gli attacchi?? 57-54 mi sembra ancora un po' tantino, prova 55-50
Larghezza tavola
Re: Larghezza tavola
Può essere, solo che volevo fare un passaggio graduale.mariomoto wrote:Quoto Mik, Jax devi andere giu' piu' deciso con le tavole larghe, possibile che non riesci ad aprire di piu'
gli attacchi?? 57-54 mi sembra ancora un po' tantino, prova 55-50
La prossima volta provo.
You take the red pill-you stay in Wonderland,I show you how deep the rabbit-hole goes.
https://www.carvers.it
https://www.carvers.it
Re: Larghezza tavola
Secondo me 50-55 è l'ottimo!JaX wrote:Può essere, solo che volevo fare un passaggio graduale.mariomoto wrote:Quoto Mik, Jax devi andere giu' piu' deciso con le tavole larghe, possibile che non riesci ad aprire di piu'
gli attacchi?? 57-54 mi sembra ancora un po' tantino, prova 55-50
La prossima volta provo.
Re: Larghezza tavola
Spero di arrivarci, la prossima volta ci provo ma temo di uscire comunque.pantans wrote:Secondo me 50-55 è l'ottimo!
You take the red pill-you stay in Wonderland,I show you how deep the rabbit-hole goes.
https://www.carvers.it
https://www.carvers.it
Re: Larghezza tavola
Jax mi ricordo che avevi 2 belle scialuppe e 50/55 con il 22 esce troppo il boot, ma se stai dentro
dovresti togliere gli spessori con angolature sotto i 50 non servono....vedrai che acquisti + sensibilità e a pieghe estreme hai + tenuta xche' si riduce drasticamente lo chattering, se riesci a superare la fase iniziale vedrai che non metterai + spessori
dovresti togliere gli spessori con angolature sotto i 50 non servono....vedrai che acquisti + sensibilità e a pieghe estreme hai + tenuta xche' si riduce drasticamente lo chattering, se riesci a superare la fase iniziale vedrai che non metterai + spessori
COILER EXTREMECARVE ECVC / UPZ RC10 & DGSS
https://www.youtube.com/watch?v=I9w7MVk7k0M
https://www.youtube.com/watch?v=I9w7MVk7k0M
Re: Larghezza tavola
Ci avevo provato tempo fa ma mi ero trovato malissimo...
You take the red pill-you stay in Wonderland,I show you how deep the rabbit-hole goes.
https://www.carvers.it
https://www.carvers.it
Re: Larghezza tavola
Tranquillo e' normale non mollare riprova
3/ 4 uscite e non ci pensi+
guarda il board width calculator http://www.donek.com/product/rev/
3/ 4 uscite e non ci pensi+
guarda il board width calculator http://www.donek.com/product/rev/
COILER EXTREMECARVE ECVC / UPZ RC10 & DGSS
https://www.youtube.com/watch?v=I9w7MVk7k0M
https://www.youtube.com/watch?v=I9w7MVk7k0M
Re: Larghezza tavola
Con il calculator impostando la misura più piccola di scarpone, esce una larghezza più grande delle tavole che producono.
Re: Larghezza tavola
Non che producono, che sono in catalogo, Sean te le fa larghe quanto vuoi.
You take the red pill-you stay in Wonderland,I show you how deep the rabbit-hole goes.
https://www.carvers.it
https://www.carvers.it
Re: Larghezza tavola
Comunque sia i valori che escono dal calcolatore sono fuori misura per qualsiasi produttore. Boh?!